如今人們對高性能的機械設備的需求與日俱增，對機器日益增長的功能及工作效率的要求，導致機器的速度更快，受力更廣，應用范圍更廣，也導致了對潤滑油的要求不斷增加。
福斯的工業用油順應了當代工業發展的潮流。這些油品具有的優良品質，遠遠超過機械廠家的規格與指標。換油周期的延長及維修費用的降低，都能助您降低成本。
福斯工業用油有相當廣的應用范圍和極高的使用壽命，該特點提供了最優的潤滑性及最低的損耗，甚至在高負荷情況下亦是如此。
|
產品名稱 |
ISO粘度
等級 |
粘度
指數 |
開口閃點
℃ |
傾點
℃ |
主要應用 |
|
RENOLIN B 10
RENOLIN B 15
RENOLIN B 20 |
32
46
68 |
100
100
100 |
190
210
220 |
-27
-27
-24 |
通用型抗磨液壓油，用于對油品氧化、老化、抗磨及抗乳化性能有要求的場合，滿足并超過DIN HLP及ISO HM 等級。 |
|
RENOLIN B 32 HVI
RENOLIN B 46 HVI |
32
46 |
170
170 |
175
180 |
-36
-33 |
低凝抗磨液壓油，用于所有液壓系統，特別是要求高粘度指數的場合。如寒冷地區或低溫環境機器設備的液壓系統，露天作業的機器設備及工作溫度極大的液壓裝置。滿足并超過DIN HVLP及ISO HV 等級。 |
|
RENOLIN MR 0
RENOLIN MR 1
RENOLIN MR 3
RENOLIN MR 5
RENOLIN MR 10
RENOLIN MR 15
RENOLIN MR 20
RENOLIN MR 30 |
2
5
10
22
32
46
68
100 |
--
--
105
100
100
100
100
95 |
75
85
160
165
200
220
225
230 |
-42
-33
-30
-30
-30
-30
-27
-21 |
多用途潤滑油，具有良好的抗氧化性及粘溫性能，同時還有突出的防銹、清潔、抗磨性能。Renolin MR 0,MR 1,MR 3 是機床及紡織機器主軸/錠子用油。Renolin MR 5/10/20 屬于極壓性液壓油，可在100℃的高溫下持續使用，并提供優異的防銹保護。Renolin MR 30 用于較大的齒輪箱中，亦可作為初裝及防銹油。
Renolin MR 系列產品滿足并超過DIN HLPD/CLP及ISO HMD/CKC等級。 |
|
HYDROTHERM 46 NP 3 |
46 |
170 |
-- |
45 |
乙二醇基的抗燃液壓油，用于接近高溫、火焰及有防火要求的液壓循環系統，主要用于冶煉、礦山、注塑成型等行業的液壓設備。滿足并超過DIN/ISO HFC 等級。 |
RENOLIN B
|
|
 |
High Quality HM Hydraulic Oils and CKC Lubricating Oils
|
|
High Quality HM Hydraulic Oils and CKC Lubricating Oils
The function and operational reliability of hydraulic systems depends largely on the quality of the hydraulic fluids used which, apart from transfering forces, must also seal, cool and lubricate. Because hydraulic oils are subject to a variety of stresses, they must fulfil a number of requirements. These must be maintained throughout the service life of the oil and must help combat the formation of undesirable reaction by-products. The RENOLIN B series of oils are based on highly ageing resistant solvent raff inates and fulfill, and in many points surpass, the minimum requirements made on HM hydraulic oils according to ISO 6743-4.
The RENOLIN B series of oils offer the following advantages:
- Good EP properties and thus protection against wear
- Good viscosity-temperature behaviour
- Excellent oxidation stability and resistance to ageing
- Excellent corrosion protection
- Rapid air release and low foaming
- Good demulsification characteristics
- Good elastomer compatibility
Application:
The RENOLIN B series of oils are not just high grade hydraulic oils. They are also excellent CKC lubricating oils according to ISO 6743-6 which can be used for numerous applications such as gearboxes and bearings.
| RENOLIN |
|
B 3 |
B 5 |
B 10 |
B 15 |
B 20 |
B 30 |
|
| acc. to ISO 6743-4 |
|
HM 10 |
HM 22 |
HM 32 |
HM 46 |
HM 68 |
HM 100 |
|
| acc. to DIN 51 502 |
|
HLP 10 |
HLP 22 |
HLP 32 |
HLP 46 |
HLP 68 |
HLP 100 |
|
| Characteristics |
Unit |
|
|
|
|
|
|
Test method |
| Colour |
|
1 |
1 |
1 |
1.5 |
2 |
2.5 |
ASTM D 1500 |
| Kinematic viscosity |
|
|
|
|
|
|
|
|
| at 40 °C |
mm2/s |
10 |
22.4 |
32 |
47 |
67 |
100 |
ASTM D 445 |
| at 100 °C |
mm2/s |
2.5 |
4.4 |
5.6 |
7.1 |
8.6 |
11 |
ASTM D 445 |
| Viscosity index |
|
61 |
105 |
114 |
109 |
99 |
94 |
ASTM D 2270 |
| Density at 15 °C |
kg/l |
0.85 |
0.865 |
0.88 |
0.88 |
0.882 |
0.888 |
ASTM D 1298 |
| Flash point, Cleveland open cup |
°C |
160 |
163 |
188 |
210 |
224 |
232 |
ASTM D 92 |
| Pour point |
°C |
- 27 |
- 30 |
- 27 |
- 27 |
-24 |
- 21 |
ASTM D 97 |
| Neutralization number |
mg KOH/g |
0.3 |
0.3 |
0.3 |
0.3 |
0.3 |
0.3 |
ASTM D 974 |
| Saponification number |
mg KOH/g |
0.6 |
0.6 |
0.6 |
0.6 |
0.6 |
0.6 |
ASTM D 94 |
| Oxide ash |
% mass |
0.2 |
0.2 |
0.2 |
0.2 |
0.2 |
0.2 |
ASTM D 482 |
| Water content |
% mass |
not traceable |
not traceable |
not traceable |
not traceable |
not traceable |
not traceable |
ASTM D 95 |
| Insolubles |
% mass |
not traceable |
not traceable |
not traceable |
not traceable |
not traceable |
not traceable |
DIN 51 592 |
| Demulsification |
min |
15 |
15 |
15 |
15 |
15 |
15 |
DIN 51 599 |
| Air release at 50 °C |
min |
1 |
3 |
6 |
7 |
8 |
16 |
ASTM D 3427 |
| Foaming, |
|
|
|
|
|
|
|
|
| seq. I |
ml |
35/0 |
5/0 |
20/0 |
10/0 |
20/0 |
10/0 |
ASTM D 892 seq. I-III |
| seq. II |
ml |
10/0 |
10/0 |
20/0 |
40/0 |
30/0 |
30/0 |
ASTM D 892 seq. I-III |
| seq. III |
ml |
35/0 |
5/0 |
20/0 |
10/0 |
20/0 |
10/0 |
ASTM D 892 seq. I-III |
| Copper corrosion |
degree of corr. |
1a-100A24 |
1a-100A24 |
1a-100A24 |
1a-100A24 |
1a-100A24 |
1a-100A24 |
ASTM D 130 |
| Rust prevention |
|
pass A |
pass A |
pass A |
pass A |
pass A |
pass A |
ASTM D 665 |
| FZG mechanical gear rig test |
load stage |
12 |
12 |
12 |
12 |
12 |
12 |
DIN 51 354-2 |
| Vickers vane pump test, loss of mass |
|
|
|
|
|
|
|
|
| on ring |
mg |
< 120 |
< 120 |
< 120 |
|
|
|
IP 281 |
| on vanes after 250 h |
mg |
< 30 |
< 30 |
< 30 |
|
|
|
IP 281 |
| Effect on SRE-NBR 1 seal material acc. to DIN 53 538-1 at 100 °C +/– 1 °C after 7 days +/– 2 hours, relative volume change |
|
|
|
|
|
|
|
|
| change in Shore A |
% |
15 |
7 |
5 |
5 |
5 |
5 |
DIN 53 521 together with DIN 53 505 |
| hardness |
Shore |
- 2 |
- 1 |
- 1 |
- 1 |
- 1 |
- 1 |
DIN 53 521 together with DIN 53 505 |
|
| | |
|
|
